Objective : This method of test covers the procedure for determining the aggregate impact
value of coarse aggregate.
Reference : IS : 2386 ( Part IV) – 1963, IS: 383-1970
Theory : The aggregate impact value‘ gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from its resistance to a slow compressive load.
Apparatus : An impact testing machine of the general form shown in Fig. 2 and complying with the following:
1. A cylindrical steel cup of internal dimensions: Diameter 102 mm, Depth 50 mm and not less than 6.3 mm thick
2. A metal hammer weighing 13.5 to 14.0 kg, the lower end of which shall be cylindrical in shape, 100.0 mm in diameter and 5 cm long, with a 2 mm chamber at the lower edge, and case-hardened. The hammer shall slide freely between vertical guides so arranged that the lower (cylindrical) part of the hammer is above and concentric with the cup.
3. Means for raising the hammer and allowing it to fall freely between the vertical guides from a height of 380.0 mm on to the test sample in the cup, and means for adjusting the height of fall within 5 mm. Sieves-The IS Sieves of sizes 12.5, 10 and 2.36 mm, Tamping Rod, balance of capacity not less than 500 g, Oven etc.
Procedure :
1. The test sample shall consist of aggregate the whole of which passes a 12.5 mm IS Sieve and is retained on a 10 mm IS Sieve. The aggregate comprising the test sample shall be dried in an oven for a period of four hours at a temperature of 100 to 110°C and cooled.
2. The measure shall be filled about one-third full with the aggregate and tamped with 25 strokes of the rounded end of the tamping rod. The net weight of aggregate in the measure shall be determined to the nearest gram (Weight A)
3. The impact machine shall rest without wedging or packing upon the level plate, block or floor, so
that it is rigid and the hammer guide columns are vertical.
4. The cup shall be fixed firmly in position on the base of the machine and the whole of the test sample placed in it and compacted by a single tamping of 25 strokes of the tamping rod.
5. The hammer shall be raised until its lower face is 380 mm above the upper surface of the aggregate
in the cup, and allowed to fall freely on to the aggregate. The test sample shall be subjected to a total
of 15 such blows each being delivered at an interval of not less than one second.
6. The crushed‘ aggregate shall then be removed from the cup and the whole of it sieved on the 2.36
mm IS Sieve until no further significant amount passes in one minute. The fraction passing the sieve
shall be weighed to an accuracy of 0.1 g (Weight. B).
7. The fraction retained on the sieve shall also be weighed (Weight C) and, if the total weight (C+B) is less than the initial weight (Weight A) by more than one gram, the result shall be discarded and a
fresh test made. Two tests shall be made.
Calculation :
The ratio of the weight of fines formed to the total sample weight in each test shall he expressed as a
percentage, the result being recorded to the first decimal place:
Aggregate Impact Value=B/A*100
B weight in g of fraction passing through 2.36 mm IS Sievs
A weight in g of saturated surface - dry sample,
Conclusion / Result :
The aggregate Impact value of given sample of coarse aggregate is ……….. %
The aggregate impact value should not be more than 45 percent for aggregate used for concrete other than for wearing surfaces, and 30 percent for concrete used for wearing surfaces such a runways, roads and air field pavements.
value of coarse aggregate.
Reference : IS : 2386 ( Part IV) – 1963, IS: 383-1970
Theory : The aggregate impact value‘ gives a relative measure of the resistance of an aggregate to sudden shock or impact, which in some aggregates differs from its resistance to a slow compressive load.
Apparatus : An impact testing machine of the general form shown in Fig. 2 and complying with the following:
1. A cylindrical steel cup of internal dimensions: Diameter 102 mm, Depth 50 mm and not less than 6.3 mm thick
2. A metal hammer weighing 13.5 to 14.0 kg, the lower end of which shall be cylindrical in shape, 100.0 mm in diameter and 5 cm long, with a 2 mm chamber at the lower edge, and case-hardened. The hammer shall slide freely between vertical guides so arranged that the lower (cylindrical) part of the hammer is above and concentric with the cup.
3. Means for raising the hammer and allowing it to fall freely between the vertical guides from a height of 380.0 mm on to the test sample in the cup, and means for adjusting the height of fall within 5 mm. Sieves-The IS Sieves of sizes 12.5, 10 and 2.36 mm, Tamping Rod, balance of capacity not less than 500 g, Oven etc.
Procedure :
1. The test sample shall consist of aggregate the whole of which passes a 12.5 mm IS Sieve and is retained on a 10 mm IS Sieve. The aggregate comprising the test sample shall be dried in an oven for a period of four hours at a temperature of 100 to 110°C and cooled.
2. The measure shall be filled about one-third full with the aggregate and tamped with 25 strokes of the rounded end of the tamping rod. The net weight of aggregate in the measure shall be determined to the nearest gram (Weight A)
3. The impact machine shall rest without wedging or packing upon the level plate, block or floor, so
that it is rigid and the hammer guide columns are vertical.
4. The cup shall be fixed firmly in position on the base of the machine and the whole of the test sample placed in it and compacted by a single tamping of 25 strokes of the tamping rod.
5. The hammer shall be raised until its lower face is 380 mm above the upper surface of the aggregate
in the cup, and allowed to fall freely on to the aggregate. The test sample shall be subjected to a total
of 15 such blows each being delivered at an interval of not less than one second.
6. The crushed‘ aggregate shall then be removed from the cup and the whole of it sieved on the 2.36
mm IS Sieve until no further significant amount passes in one minute. The fraction passing the sieve
shall be weighed to an accuracy of 0.1 g (Weight. B).
7. The fraction retained on the sieve shall also be weighed (Weight C) and, if the total weight (C+B) is less than the initial weight (Weight A) by more than one gram, the result shall be discarded and a
fresh test made. Two tests shall be made.
Calculation :
The ratio of the weight of fines formed to the total sample weight in each test shall he expressed as a
percentage, the result being recorded to the first decimal place:
Aggregate Impact Value=B/A*100
B weight in g of fraction passing through 2.36 mm IS Sievs
A weight in g of saturated surface - dry sample,
Conclusion / Result :
The aggregate Impact value of given sample of coarse aggregate is ……….. %
The aggregate impact value should not be more than 45 percent for aggregate used for concrete other than for wearing surfaces, and 30 percent for concrete used for wearing surfaces such a runways, roads and air field pavements.
No comments:
Post a Comment